• Skip to primary navigation
  • Skip to main content
  • Skip to primary sidebar

Circuit Ideas for You

Get free circuit ideas online.

  • Home
  • Privacy Policy
  • About
Home » How to Illuminate 18 LEDs from a 3.7V Battery

How to Illuminate 18 LEDs from a 3.7V Battery

Last updated on 18 July 2025 by Admin-Lavi Leave a Comment

In this post for How to Illuminate 18 LEDs from a 3.7V Battery we need to power 18 LEDs with 3.7V battery like a small light party!

To light all LEDs well we need smart plan.

We have to make small LED groups and connect in clever way.

Use series in line and parallel in row and this will control voltage and current and so LEDs shine bright without any burn.

Circuit Working:

How to Illuminate 18 LEDs from a 3.7V Battery Diagram

Parts List:

CategoryDescriptionQuantity
Resistors1k, 10Ω (1/4 watt each)1 each
10k (1/4 watt)2
CapacitorsCeramic 10nF1
Electrolytic 100μF 25V1
SemiconductorsTransistors BC547, 2N22221 each
Inductor 1mH1
LEDs white straw hat 5mm, 20mA18
ON/OFF switch1
Li-ion Battery 3.7V1

This circuit uses 3.7V Li-Ion battery to light 18 white LEDs and parts come from old CFL lamp.

It uses two transistors like 2N2222 and BC547 to keep brightness same always.

BC547 give feedback to keep circuit working.

Even with high 10k resistor it rans 12 hours on 1200mAh battery and brightness stay steady.

2N2222 control how bright LEDs shine, it get small current from 10k resistor but because of gain from 100 to 300 the output current goes up to 100mA.

LEDs run slightly over limit but BC547 help control it and turn OFF 2N2222 at right time so it doe not stay ON too long.

10k and 1k resistors make voltage divider to set timing.

When 2N2222 turn ON, 10 ohm resistor makes voltage that delays turns ON a bit.

1nF capacitor set how fast circuit oscillates which turns ON/ OFF

By changing these four parts like resistors and capacitor we can get and keep the right brightness for whole battery life.

LEDs in each string are in series.

For even brightness all strings must match.

We can swap LEDs to balance the brightness.

Formulas:

Using boost converter and we can increase 3.7V battery to higher voltage for 18 LEDs in series or parallel.

Important boost converter formulas:

1. Output Voltage (Vout):

Vout = Vin / (1 − D)

  • Vin is the input voltage for 3.7V
  • D is the duty cycle for how long switch is ON

2. Inductor Current (IL):

IL = Vout × D × T / L

  • T is the time of one switch cycle
  • L is the inductor value

3. Duty Cycle (D):

D = (Vout − Vin) / Vout

4. Choose Inductor (L):

L ≥ (Vout − Vin) × Vout / (f × ΔIL)

where,

  • f is the switch frequency
  • ΔIL is the ripple current in inductor

These formulas help design good boost converter.

With this we can light up 18 LEDs using 3.7V battery.

Ensure to check LED forward voltage to match circuit design.

How to Build:

How to Illuminate 18 LEDs from a 3.7V Battery find out the below mentioned steps for connection of components.

  • Connect batteries positive (+) to positive supply line through an ON/OFF switch.
  • Connect batteries negative (–) to ground.
  • Connect collector of transistor Q1 to positive supply through resistor R1.
  • Connect base of Q1 between resistor R2 and capacitor C2.
  • Connect emitter of Q1 to ground.
  • Connect capacitor C1 from positive supply to ground for power smoothing.
  • Place a 1mH inductor between R1 and collector of Q2 in the positive line.
  • Connect collector of Q2 to positive supply.
  • Connect base of Q2 between R1 and collector of Q1.
  • Connect emitter of Q2 to ground through resistor R4.
  • Connect resistor R3 between R2 and C2.
  • Connect 18 straw hat white LEDs in series from positive supply to ground as shown in the circuit diagram above.

Important Notes:

  • Cover circuit well to avoid short circuits.
  • Always use current limiting resistors to protect LEDs.
  • Too much current can overheat and damage LEDs.

Conclusion:

In this article for How to Illuminate 18 LEDs from a 3.7V Battery it must be designed smartly to match voltage and current needs.

Our goal should be bright light with less power loss.

References:

Is 3.7V LiPo suitable to power arduino+led strip?

Filed Under: LED and Lamps

About Admin-Lavi

Lavi is a B.Tech electronics engineer with a passion for designing new electronic circuits. Do you have questions regarding the circuit diagrams presented on this blog? Feel free to comment and solve your queries with quick replies

Previous Post: « Buck Converter Circuit for 1 Watt LED Driver
Next Post: Simple Solar Garden Light Circuit using One Transistor »

Reader Interactions

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Primary Sidebar




Categories

  • Alarm Circuits (31)
  • Amplifier Circuits (67)
  • Arduino Projects (30)
  • Audio Circuits (93)
  • Automobile Circuits (19)
  • Battery Charger Circuits (48)
  • Free Energy (13)
  • Heater and Temperature Controllers (9)
  • High Voltage (1)
  • Indicator Circuits (38)
  • Inverter Circuits (13)
  • LDR Circuits (14)
  • LED and Lamps (114)
  • Meters and Testers (27)
  • Motor Controllers (18)
  • Oscillator Circuits (32)
  • Power Supply Circuits (91)
  • Remote Control Circuits (6)
  • Security and Protection (23)
  • Sensors and Detectors (74)
  • Solar Circuits (16)
  • Timer Circuits (28)
  • Transistor Circuits (56)
  • Transmitter Circuit (12)
  • Tutorials (4)
  • Water Level Controller (4)

Recent Posts

  • Low Power Led Flasher Circuit using Nand Gate IC
  • Two Star Flasher Circuit with 555 IC
  • Automatic Light Control Switch Circuit using IC 555
  • Ultrasonic Blind Stick Circuit using Arduino
  • Simple Humidity Level Detector Circuit

Recent Comments

  1. Admin-Lavi on Constant Voltage, Constant Current Battery Charger Circuit
  2. Bill on Constant Voltage, Constant Current Battery Charger Circuit
  3. Admin-Lavi on Long Range FM Transmitter Circuit (2km)
  4. Sina on Long Range FM Transmitter Circuit (2km)
  5. Admin-Lavi on Long Range FM Transmitter Circuit (2km)

Copyright © 2025 | New Circuit Ideas